State of Affairs – Nine of Cups, Blue & the Crew
/Here's what's happening with Nine of Cups, Blue & crew and a little insight into our plans for 2018.
Read MoreHere's what's happening with Nine of Cups, Blue & crew and a little insight into our plans for 2018.
Read MoreWe are finally making some progress on the chainplates, although it has been one step backwards for each two slow steps forward. The most recent setback was when I discovered, after the stainless for the chainplates was all cut, drilled and polished, that the metal for the backstays was the wrong thickness – 3/8” (10mm) instead of 1/2” (12mm). We will lose another week while they are redone.
There are two bends that need to be made in each chainplate, but determining the location of each bend has to wait until the part is attached to the hull. Once attached, the precise location and angle of the first bend can be measured and marked, then the chainplate must be removed and taken back to the machinist to be bent. Next the parts will be reattached to the hull, the second bend measured and marked, and again sent to the shop to be bent. All this has to wait until the holes have been drilled in the hull.
Most of the holes in the hull have now been drilled, which was a major undertaking. A total of 68 holes needed to be drilled, most of which pass not only through the hull, but the old stainless chainplates as well. All but eight of these have been drilled, and these remaining holes will wait until the first bend is made and the chainplates reattached. One thing we noticed as the holes were drilled was that rust colored water continues to seep out from the old chainplates – continued confirmation that we are doing the right thing here and didn't wait any longer.
The exterior carpentry is done. The last phase was fabricating and attaching the teak spacers to the hull, and this has now been completed.
The interior cutouts have all been made, luckily, except for one in the forward berth, they are all inside bookshelves or lockers. I used my Ryobi version of the Fein tool to make the cuts. I will make teak pieces to cover the holes – a few in the next few days with the teak I have on hand and some later when I can get less expensive teak elsewhere. I want to be able to easily remove the hole covers later so that the new chainplates and bolts can be inspected periodically.
Progress is being made, although painfully slow. Maybe another week until the project is complete – assuming no more major setbacks. Using Marcie's project formula, it'll be another two weeks.
We are making some progress on the new chainplates. Now that the metal has been cut, the machinist came down to look at Nine of Cups and take some measurements. Sort of like “Ready, Fire, Aim...” in my mind. There was some initial angst when we thought the chainplates had been cut too short, but after talking it through with the shipwright and with Dave, we all agreed the newly cut metal would work.
The marine architect made an appearance as well. He did the original design based on photos, assuring us that he knew the boat quite well and that a trip to the yacht club to actually look at Cups was unnecessary. This was borne out, as you may remember, when his first iteration of the design was totally incorrect, having the chainplates bolted to the bulwark and into the core of the deck. We had a discussion, now moot since the metal was already cut, about how the chainplates might have been designed to look less industrial and more aesthetically pleasing. He gave us several less than compelling reasons why this wasn't done, such as “it would have added extra weight to the boat” (two pounds in extra metal would make a difference on our 21 ton boat?), “designs that bolted the chainplates into the bulwark wouldn't be as strong” (not something I was suggesting, and anyway, wasn't that exactly the way he first designed it???), blah, blah, blah … We weren't really impressed.
The shipwright came shortly after, and following much measuring and discussion, he drilled a small exploratory hole through the hull to determine how thick it was and where the bolts would protrude into the interior. When the bit came into contact with the old chainplate, water started running out of the hole – maybe a teaspoon or two. If water had made it that far into the hull, approximately two feet down from the cap rail, it was almost certain that the old chainplates would be suffering from crevice corrosion – more confirmation that we were doing the right thing. Another small hole was drilled alongside the chainplate, and no water came out, some assurance, at least, that the water ingress was confined to the column alongside the chainplate.
We are now waiting for the machinist to drill the holes in the chainplates and polish the stainless steel to a mirror finish, after which the hull drilling and cutting will begin in earnest. I sound quite negative, but in actuality, I am still optimistic that the project will turn out fine.
Stay tuned...
Hi there and welcome to Just A Little Further!
We are David and Marcie Lynn and we've lived aboard our Liberty 458 cutter-rigged sailboat since 2000.
What began as an urge to travel slowly and economically at our own pace ended up an adventure of a lifetime.
Well, here we are ... nearly 90,000 miles under the keel, 5 continents, 5 Great Southern Capes, 36 countries and almost two decades later, still taking one passage at a time and going just a little further.